Phil’s Lab

BGA PCB Design Tips - Phil's Lab #95

SDRAM Hardware & Firmware Tutorial (STM32) - Phil's Lab #80

FPGA/SoC Board Bring-Up - QSPI (Zynq Part 3) - Phil's Lab #98

Series Termination Basics - Phil's Lab

I2C Hardware & PCB Design - Phil's Lab

PCB Chip Antenna Hardware Design - Phil's Lab

PCB Traces 101 - Phil's Lab

ESP32 + PCB Antenna Hardware Design Tutorial - Phil's Lab #90

RC Low-Pass Filter Deep-Dive - Phil's Lab

Flight Control System Design: Hardware and PCB Design with KiCAD - Phil's Lab #1

PID Controller Implementation in Software - Phil's Lab #6

STM32 Programming Tutorial for Custom Hardware | SWD, PWM, USB, SPI - Phil's Lab #13

How To Write A Driver (STM32, I2C, Datasheet) - Phil's Lab #30

Audio EQ Software Implementation (STM32) - Phil's Lab #89

Embedded Linux + FPGA/SoC (Zynq Part 5) - Phil's Lab

STM32 Real-Time FIR Filter Implementation (CMSIS DSP) - Phil's Lab

Recursive RMS (STM32 Implementation) - Phil's Lab

Advanced Digital Hardware Design (Course Release) - Phil's Lab

BGA PCB Design Tips - Phil's Lab #95

Raspberry Pi RP2040 Hardware Design | Altium Designer | JLCPCB - Phil's Lab #28

STM32H7 ADC + DMA + Timer Firmware Tutorial - Phil's Lab

PCB Design for Manufacturing Tips (DFM) - Phil's Lab #40

STM32 + LCD Display (FMC) Firmware Tutorial - Phil's Lab

KiCad 6 STM32 PCB Design Full Tutorial - Phil's Lab #65

How To Write A Driver (Audio CODEC & I2C) - Phil's Lab

ESP32 Programming Tutorial for Custom Hardware (GPIO, Serial, SPI, WiFi) - Phil's Lab #91

STM32 + SWD + ST-Link + CubeIDE | Debugging on Custom Hardware Tutorial - Phil's Lab #4

KiCad 7 STM32 Bluetooth Hardware Design (1/2 Schematic) - Phil's Lab

RC High-Pass Filters Explained - Phil's Lab

How PCBs are Manufactured & Assembled (PCBWay Factory Tour) - Phil's Lab

KiCad 7 STM32 Bluetooth Hardware Design (2/2 PCB) - Phil's Lab

PCB Design Final Touches (Tips & Checklist) - Phil's Lab

How To Read A Datasheet - Phil's Lab

System Identification with Matlab - Control System Design 3/6 - Phil's Lab #9

FPGA/SoC Board Bring-Up Tutorial (Zynq Part 1) - Phil's Lab #96

Noise Gate - DSP with STM32 - Phil's Lab #58

Accelerometers and Gyroscopes - Sensor Fusion #1 - Phil's Lab #33

FPGA/SoC Board Bring-Up - DDR3 (Zynq Part 2) - Phil's Lab #97

Comb Filters & Delay Lines in Software (STM32) - Phil's Lab

Interfacing FPGAs with DDR Memory - Phil's Lab

USB-C Power Delivery Hardware Design - Phil's Lab

LDO Regulator Hardware Design - Phil's Lab

Thermal PCB Design Tips - Phil's Lab #93

STM32 + LVGL Firmware Tutorial - Phil's Lab

QFN PCB Design Tips & Tricks - Phil's Lab

Mixed-Signal Hardware/PCB Design Tips - Phil's Lab #88

Schematic Tips & Tricks - Phil's Lab #62

How To Improve Your PCB Designs (Common Mistakes) - Phil's Lab #18

High-Speed PCB Design Tips - Phil's Lab #25

Real-Time Software Implementation of Analog Filters - Phil's Lab #20

FPGA + PCIe Hardware Accelerator Design Walkthrough (DDR3, M.2, ..) - Phil's Lab #82